Why Is My Garage Door Crooked?

Short answer: A garage door becomes crooked when one side lifts or hangs lower than the other. This condition typically occurs when a lift cable snaps or slips off its drum, a...

By Everyday Home Advice Editorial Team

Black paneled garage door on a residential home exterior

Short answer: A garage door becomes crooked when one side lifts or hangs lower than the other. This condition typically occurs when a lift cable snaps or slips off its drum, a torsion spring breaks, a roller exits the track, or a track bends. In North Texas, foundation movement from expansive clay soil can also throw the door frame out of square. Operating a crooked door can bend the panels, destroy the opener gears, or cause the door to crash down. Stop using the door immediately and disengage the automatic opener until it is evaluated.

Identifying a crooked garage door and its risks

A garage door should remain horizontal and parallel to the header and floor throughout its travel. When a door hangs unevenly, a visible gap appears at the bottom on one side while the other side touches the ground. You may also notice the door jamming in the tracks, grinding loudly, or stopping mid-cycle. Allowing a crooked door to operate poses serious physical safety risks and severe structural damage to the system. Garage doors weigh hundreds of pounds and rely on counterbalanced tension to move smoothly. When the tension becomes uneven, the remaining hardware bears the full weight of the door. Operating the opener in this state can strip the opener drive gears, bend the aluminum or steel tracks, snap the remaining cable, or cause the entire door assembly to pull free from the wall framing.

Primary causes of uneven garage door movement

Several mechanical failures can cause a garage door to sag or lift unevenly. Understanding how these components fail helps identify the severity of the issue.

Broken springs or unequal spring tension

Torsion springs mounted above the door header or extension springs along the overhead tracks provide the force needed to lift the door. On systems with two springs, one spring can snap while the other remains intact. The side with the intact spring continues to lift, while the side with the broken spring drags, creating a steep angle during travel.

Cable slip or failure

Lift cables run from the bottom brackets of the door to drums mounted on the torsion shaft. If a cable snaps due to rust or friction, the door drops immediately on that side. Alternatively, if the cable jumps off the grooves of the drum, one side loses tension while the other remains taut, leaving the door crooked.

Track misalignment and roller displacement

Vertical and horizontal tracks guide the rollers mounted on the door panels. If a roller binds or wears out, it can pop entirely out of the track channel. Vehicle impacts, loose track bracket bolts, or track distortion can also pinch the door on one side while the other side continues moving.

North Texas environmental and structural factors

Homes in the Dallas-Fort Worth area face distinct climate and structural conditions that contribute to garage door misalignment. Expansive clay soil throughout the region expands significantly when wet and contracts during prolonged dry spells. As soil moisture shifts between heavy seasonal rains and dry summer months, concrete slab foundations settle and shift. When a garage floor or header moves even a fraction of an inch, the garage door frame pulls out of square. This structural distortion places binding pressure on the tracks and forces the door to bind or hang crooked. Extreme summer heat also impacts garage door hardware. West-facing garages endure intense afternoon sun and high attic temperatures. Metal tracks and wide door panels expand under extreme heat, narrowing track tolerances and putting extra drag on rollers. Over time, heat accelerates metal fatigue in high-tension steel springs and causes lubricant to break down, increasing friction and cable slippage.

Safe homeowner inspection steps and safety hazards

Homeowners can safely perform a visual check from inside the garage with the door completely closed. Stand away from the path of the door and look for obvious signs of damage. Examine the springs above the door or along the tracks for a visible gap in the coils, which indicates a break. Inspect the lift cables on both sides to see if one is hanging loose, frayed, or unspooled from the drum. Look along the vertical tracks to check if all rollers are seated inside the steel channels. Check the bottom rubber seal to see if foundation settling has created a wedge-shaped gap against the floor. Never attempt to adjust, loosen, or remove high-tension components. Torsion springs, center-bearing brackets, bottom roller brackets, and lift cables are under extreme mechanical tension. Attempting to repair these parts without specialized tools can cause catastrophic injury. Do not pull the manual emergency release rope if the door is stuck open, as a door missing cable tension will crash down immediately.

What a professional technician tests and repairs

Because Texas does not issue a state license specifically for garage door technicians or general home repair contractors, homeowners should hire qualified, insured local specialists. A technician will perform a full diagnostic assessment of the system. The technician inspects cable tension, drum alignment, shaft straightness, and track squareness using commercial leveling tools. They test spring balance by disconnecting the opener and lifting the door manually to check for smooth movement and proper counterweight. Repairs usually involve resetting cables onto drums, winding torsion springs to the correct tension, replacing worn rollers, or realigning vertical tracks. If a spring has broken, the technician will replace both springs. Installing a single new spring alongside an old, fatigued spring creates unequal lifting force and leads to premature failure. After mechanical repairs, the technician recalibrates the opener force settings and safety travel limits.

Repairing versus replacing a crooked garage door

In many cases, a crooked garage door can be repaired by replacing springs, re-seating cables, or straightening tracks. However, certain conditions necessitate full replacement. If the crooked operation caused the door panels to buckle, twist, or split, the structural integrity of the section is lost. Panel replacement may be possible for newer models, but matching older panel profiles and paint colors can be difficult. If multiple panels are creased or if the frame has shifted permanently out of square due to severe foundation movement, replacing the entire door and track assembly is the safest, most reliable solution.

Factors that drive repair costs and prevention

Several key factors determine the cost of correcting a crooked garage door: The type of balance system, as torsion spring systems generally require different parts and labor than extension springs. The extent of secondary damage, such as bent tracks, stripped opener gears, or damaged door sections. Whether custom track adjustments or shimming are needed to accommodate foundation movement. The weight and height of the door, as heavy insulated steel or wood doors require heavier-gauge springs and cables. To prevent alignment issues, inspect garage door hardware visually every few months. Keep tracks clean of dirt and debris, and apply a silicone-based garage door lubricant to rollers, hinges, and springs twice a year. Maintaining consistent soil moisture around your foundation with soaking hoses during dry DFW summers can also help keep the garage frame square.

Common questions

Can I pull down on the higher side of a crooked door to straighten it?

No. Forcing or pulling on a crooked garage door can bend the steel panels, pop remaining rollers out of the track, or snap the secondary cable. If the spring or cable tension is uneven, manual force will not balance the door and increases the risk of a sudden fall.

Why is my garage door crooked only when closing?

A door that appears straight when open but becomes crooked while closing often has a track alignment issue, uneven cable spooling, or a binding roller. As the door descends, friction on one side causes that cable to go slack, dropping the opposite side faster.

How do I know if foundation movement caused my door to be crooked?

If the garage header or concrete floor is no longer level, you will see a diagonal or wedge-shaped gap beneath the door even when the tracks and cables appear intact. A technician can measure the frame with a level to confirm if the structure itself has shifted.